Save Time, Money AND Hard Work With an Eliminator XTreme Cover! Proudly Made in Canada!
A blue mesh line runs down the center of the cover. During the winter, ice and snow envelop the cover weighing it down in the center. As the snow melts in the spring, the water filters through the mesh line. As a result, the cover slowly rises. When the ice has melted, the cover is stretched tightly across the pool. Any debris, leaves or dirt dry up and simply blow away and your cover is clean and free of debris. Simply unhook the straps, rinse it off and fold it up. Your pool water is leaf free. You save hours of time and hard work. No more pumping water off your cover! No more piles of leaves in your pool! A superior above ground pool Winter cover unlike any other in the market! Note: Not for use with any soft sided pool models (Intex, Bestway, etc).
IMPORTANT: Do not lower water level before installing, read installation instructions for proper installation method.
Features and Benefits:
Warranty Coverage: Eliminator Xtreme Winter covers come with a 7 Year Limited Prorated Manufacturers Warranty. The manufacturer of this cover warrants this cover against defects on workmanship and materials.
This warranty will be void if the cover is damaged as a result of improper installation or use, or if damage is a result of ice, wind or low water level. Warranty does not cover any labour charges, cost of lost water or chemicals, or any other damages that may occur.
To Start a Warranty Claim:To begin a claim, please email customerservice@poolsuppliescanada.ca with a photo showing the defect(s)/damage to your Eliminator Xtreme winter cover and include a brief explanation of what occurred.
Does Your Cover Look Like This?
It COULD Look Like This!
Above ground Eliminator XTreme Winter Covers - Frequently Asked Questions
Can I use the Eliminator Xtreme Cover with my inground pool?
No - our eliminator winter covers are for aboveground swimming pools only.
Decking- What if I have a full deck around my pool?
The Eliminator Xtreme can now be stretched across the pool and onto the deck. The deck walkway however needs to be a minimum of 36" in order to anchor the straps. However, in some instances eye bolt anchors will be needed to attach the 'S' hook.
What if I have a partial deck?
In most instances the cover can switch from vertical anchors to horizontal for the deck part. Eye bolts may be required for this.
Will the cover go around a fence kit attached to the pool?
In most cases the cover will go around a fence attached to the side of the pool.
Why don't I have to drain my pool? Will draining not crack my skimmer or return?
The design of the Eliminator Xtreme pool cover is different from the traditional cover. The return jet must be plugged, and the water level should be lowered to the bottom of the skimmer screw line to insert the dam. The dam is optional to use and is an added feature to maximize water conservation. Regardless of whether the skimmer dam is used or not, the skimmer drain must be kept open and unplugged so that water is not trapped in the skimmer body. Add foam or solar blanket material inside the skimmer body to prevent ice damage.
What if I have an in-jet light in my pool?
Remove the light bulb as per normal, in most cases a rubber plug is required (#9) to seal off the return. It is not necessary to drain below the return; all that would need to be done is remove the bulb and quickly insert the plug. You might get wet, but it’s better than draining below the waterline.
Will drilling into my vertical posts crack/ rust/ weaken them? Void Warranty?
No - the system is no different than attaching a fence kit to the side of the pool. The mounting screws are 3/4" in size.
Can I or should I use my old cover and leaf net along with this new cover?
We do not see any advantage to this but it might be necessary in very high leaf areas to combine a leaf net on top of the cover.
Will attaching the cover with bungees collapse my pool?
No - the vertical bungees put very little stress on the pool.
Why can't I just attach my traditional cover with bungees that I buy at a hardware store?
No - it simply will not work. The Eliminator cover is quite different in design.
How much longer will this cover last than a traditional cover? Why?
We expect the Eliminator Xtreme to last on average up to 7 years. This is because the wind stress is much less and your cover is not sitting on water or chemicals.
Do I have to plug my return jet?
Yes - the water level must be be above the return at all times. The recommended water height is at the bottom of the skimmer.
Do I have to put the skimmer dam on?
No - this is optional. It is only there in order to maximize water conservation.
How long does it take to install? How many people?
With 2 people it will take less than 45 minutes.
Important note: Eliminator Xtreme Winter covers are not safety covers.
What Our Customers Think of the Eliminator XTreme Cover:
How to Properly Install Your Cover:
Installation note: Improper installation will void the product warranty.
Meh, the cover is nice, fits nicely but the installation hardware is atrocious. The hardware included is definitely an after thought. Like at least make the pieces attached to the pool look half decent instead of some pipe hangers from the plumbing section. Also the self tapping screws are not great for a resin post pool. Also for the cost of the pool an 8mm socket with a magnet would be a nice touch...
Long lasting and very strong cover. we're from nfld and we havent had to buy another cover for almost 3 years now
Please log in to write a review:
Enter your postal code to check your area.